operate and maintenance of Nitrogen Unit 90K, 180K, 230K and o repacking Booster Pump Seal and Fluid End. o Well Service (Nitrogen, Cementing, Stimulation and Filtration Services). o Well Integrity Test and Subsurface Integrity Test. o Process Service (N2/He Leak Testing & N2 purging, Test Pack Pre-engineering and o Nitrogen/Helium Leak Test o Pipeline Service (Pigging, Cleaning, Flooding, Hydrotesting and Air Drying Pneumatic o Testing (Strength Test). o Calibrate Over Pressure Protection & Low Temperature Protection and Masspect (UL- o 300, UL-200, ASM 142S and PHD-4/Portable, Helium Detection. Ultrasonic Tester. o Familiar with Oil in Water Analyzer TD-500D o P&ID and Isometric Drawing knowledge. o Assisting in Nitrogen Membrane, Compressor N2 pumps, power packs etc o Maintained the fluid end for operational standard including changing of fluid end completely with no supervision. o Conversant with different types of rigs- up as per job requirements – acid job, proppant stimulation, nitrogen services, pin-point stimulation etc. o Functioned as Grounds man- rebuilding irons and valves, providing maintenance support and spotting frac equipment. o Managed and monitored inventory of chemicals, iron and the mixing of gel and acid proces

Can be really boring, a nice mix of boring and torture, or straight up torture lol. The companies have gotten pretty strict on not getting frostbite and some enforce it. If your cold, say something and go warm up. Its not like a drilling rig where you get some wind break. When your rigging in your in a Genie basket, freezing your balls off. And feet. I recommend getting a rubber mat to stand on in the genie basket, makes a world of difference. Honestly, coil is a great gig. After rigging in, make sure all the tools are cleaned up nice and put away where they belong. When your stabbing on the well, running in, pulling, and or pumping thru the coil, NEVER stand under the Coil running up to the Injector. If that shit parts, which it does, it will drop and stab into the ground after whipping around. Avoid 30 degrees both ways infront if the coil unit/reel trailer also when pumping at high pressure, especially with nitrified fluid. As it will whip in that area. Avoid putting yourself infront of the rotating joint in the center of the drum as if it goes, it will go that way.

Monitor storage tanks and pipelines, conduct physical dips, and operate SCADA system for efficient terminal operations and product management. Perform precise calculations for daily stock, ullage, and pumpable quantities, ensuring accurate reporting and optimal inventory management. Manage pipeline operations, including pigging procedures and corrosion inhibitor injection, to maintain pipeline integrity and operational efficiency. Handling of Safety Equipment Installed on PIPE Line like Block Valve, Low/High (Suction, Discharge and Flow) Switches, PSV, ESD System and C.P. System. Conduct routine checks on tanks, valves, pumps, and pipelines for leaks; report findings. Managed Crude oil decanting operations as a supervisor. Conducted sampling, performed dip, temperature, density, and water finding tests of Bowser prior to decanting. Executed decanting operations using a centrifugal pump. Oversaw dry-out operations using inclined flooring for efficient drainage. Prepared dry-out and delivery certificates for tank lorry exits.

A Senior Service Supervisor in Frac, Stimulation, and Coil Tubing operations is responsible for planning, supervising, and executing oilfield service operations at the wellsite. This role requires strong technical knowledge, leadership skills, and the ability to manage field crews while ensuring safe and efficient job execution. The supervisor coordinates hydraulic fracturing, well stimulation, and coiled tubing operations according to the approved program and client requirements. They monitor equipment performance, maintain operational efficiency, and ensure all activities comply with company safety standards and industry regulations. A key responsibility is leading field personnel, assigning tasks, and providing technical guidance during operations. The supervisor also communicates directly with clients, engineers, and logistics teams to ensure smooth workflow and timely completion of the job. In addition, the Senior Service Supervisor is responsible for troubleshooting operational issues, maintaining accurate job reports, and ensuring proper maintenance of equipment such as pumps, blenders, coiled tubing units, and pressure control systems. Strong problem-solving skills, operational decision-making, and safety leadership are essential in this role. The position often requires working in challenging environments, managing high-pressure operations, and ensuring the highest standards of safety, quality, and service delivery while meeting project objectives.

Experienced in Land and offshore cementing operation. Mobilization, cementing calculation, inventory of equipment and chemicals, interphase with Company representatives, Data acquisition during job and presentation. Ensure equipment in good working condition. Coordinate with Engineer in delivering job as per client requirements. Supervision in Primary cementing which includes 13-3/8in , 9-5/8in and 7in casing cementation. Carry out secondary cementing which includes balanced plug cementing, bradenhead squeeze, hesitation squeeze. Other roles include mobilizing equipment , cementing calculation, chemical inventory , flymixing liner cementing job. Experienced in Land and offshore cementing operation. Mobilization, cementing calculation, inventory of equipment and chemicals, interphase with Company representatives, Data acquisition during job and presentation. Ensure equipment in good working condition. Coordinate with Engineer in delivering job as per client requirements. Supervision in Primary cementing which includes 13-3/8in , 9-5/8in and 7in casing cementation. Carry out secondary cementing which includes balanced plug cementing, bradenhead squeeze, hesitation squeeze. Other roles include mobilizing equipment , cementing calculation, chemical inventory , flymixing liner cementing job

Subject: Application for Offshore Mechanical / Maintenance Opportunities Dear [Recruitment Team / Hiring Manager], I hope this message finds you well. I am writing to express my interest in offshore mechanical and maintenance positions with your esteemed organization. I have over 11 years of experience in the manufacturing industry, working in roles such as Machinist, Supervisor, Operator, Assembly Section, and Maintenance Section. This experience has provided me with strong technical expertise in mechanical operations, CNC machining, assembly, preventive maintenance, and troubleshooting complex machinery. Currently, I am employed as a CNC Machinist at Baker Hughes, 2nd Industrial Area, Dammam, Saudi Arabia, where I ensure precision in machining operations while maintaining safety and operational efficiency. I have also supervised teams and coordinated maintenance schedules, giving me the leadership and teamwork skills required for offshore environments. I am particularly interested in roles such as Mechanical Service Technician, Assembler, or Maintenance Technician (rotation/offshore). I am fully prepared for offshore work, including rotation schedules, and am committed to maintaining high safety standards and operational excellence. Please find my resume attached for your consideration. I would greatly appreciate the opportunity to contribute to your team and look forward to your positive response. Best regards, Muhammad Waseem Contact (KSA): +966540037578

Experienced in oilfield pumping operations including cementing and stimulation services. Performed job preparation, equipment rig-up and rig-down, pressure testing, and safe execution of pumping operations on both onshore and offshore locations. Strong hands-on experience with cementing units, stimulation pumps, and surface equipment, ensuring efficient job execution while strictly following HSE standards and operational procedures. Worked effectively within multicultural teams during field operations with Halliburton and SLB. My background has provided me with strong technical skills, operational discipline, and full commitment to HSE standards and efficient job performance. I am confident that my experience can contribute positively to your operations. I would welcome the opportunity to join your team and contribute to your continued success.

Hany Mohamed Abd Elatif Mohamed (High pressure senior operator) Future City – Cairo, Egypt | +201224686399 linkedin.com/in/hany-abd-el-latif | hany.mohamed8021@yahoo.com To Whom It May Concern, Please accept this letter as a formal introduction outlining extensive professional experience and technical capabilities developed over more than fifteen years within the oil and gas services sector. Valuable hands-on expertise has been gained through assignments with leading international companies including Schlumberger, Halliburton, Baker Hughes, and SAPESCO across Egypt, Saudi Arabia, and Oman. Professional experience includes operating and maintaining high-pressure pumping equipment, performing stimulation and acidizing services, conducting hydrostatic and leak testing, managing filtration systems, and supporting pipeline pre-commissioning activities while maintaining full compliance with international HSE and operational standards. Field responsibilities have consistently involved executing critical operations in demanding environments, coordinating crews, troubleshooting mechanical issues, and applying preventive maintenance practices to ensure maximum equipment reliability, minimal downtime, and continuous production efficiency. Strong strengths include technical problem solving, resource management, safety compliance, and maintaining high performance under pressure. Continuous professional development has been supported through multiple certifications and training courses, including H2S and First Aid, Fire Fighting, Safety HSE, Safety Audit, and Lifting Equipment. Seeking the opportunity to contribute experience, operational discipline, and a strong safety-focused mindset to a professional organization committed to excellence and performance. Sincerely, Hany Mohamed Abd Elatif Mohamed

Senior Pump operator, for CTU, Snubbing, Hydraulic work over,Frac,Stimulation, and sand control. Competent for handling, rig up, mixing chemical, operate, troubleshoot and maintenance the pumping and mixing equipment, experience onshore and offshore facilities. Experience in working middle east. Perform preventive maintenance on equipment as per job standart. Comply with safety and regulations for job execution and delivery. Perform equipment check, equipment horse power test for the equipment performance and fitness. Rig up and Operate the surface discharge manifold equipment on site for the job execution. Pressure test the surface manifold equipment as per job requirements.Handling and Mixing chemical as per job mixing schedule and follow safety standards. Rig up fluid system onsite as per P&ID from DOS and job program, Frac Tank,filtration unit, Centrifugal pump, low pressure hoses and manifold, Mud tank, batch mixer and dump line. Function test the line up as per job requirements.

Here are the Roles and Responsibilities of a Nitrogen Supervisor in oilfield operations: 1. Job Planning Plan nitrogen pumping operations according to the job program. Review job procedures, safety requirements, and equipment needed. 2. Supervision of Crew Supervise nitrogen operators and helpers at the location. Assign duties to crew members and ensure proper work coordination. 3. Equipment Inspection Check nitrogen pump units, boosters, hoses, and gauges before the job. Ensure all equipment is in good working condition. 4. Safety Compliance Conduct toolbox talks before starting the job. Ensure all crew follow HSE procedures and PPE requirements. 5. Operation Monitoring Monitor pressure, rate, and nitrogen flow during pumping operations. Ensure the job is performed according to the program. 6. Communication Coordinate with company representatives, coil tubing supervisors, and other service crews. 7. Troubleshooting Identify and solve equipment or operational problems during the job. 8. Reporting Prepare job reports, equipment reports, and safety reports after completing the job. 9. Maintenance Ensure proper maintenance of nitrogen units and related equipment. 10. Safety of Crew and Equipment Maintain safe working conditions and prevent accidents during operations.

The duties of a pump operator encompass various precise technical and field aspects, most notably: Operation and Monitoring: The role begins with starting up the pumps and regulating material flow based on required specifications. This includes monitoring pressure gauges, temperatures, and flow rates to ensure the system remains within safe operating limits. Preventive Maintenance: The work is not limited to operation; it extends to periodic equipment inspections, lubricating moving parts, and replacing damaged seals to prevent leakage, thereby extending the equipment's lifespan. Troubleshooting: An operator must possess a technical sense to detect abnormal noises or vibrations that may indicate an imminent malfunction, allowing for swift intervention and repair before the problem escalates. Safety and Documentation: Strict adherence to occupational safety standards and wearing personal protective equipment (PPE) is essential, along with accurately recording daily data in logbooks to track system performance.

. Installation of Equipment Install new machines, devices, or systems at client sites. Ensure equipment is set up according to company and manufacturer specifications. Configure software, hardware, or network components when required. 2. Maintenance and Servicing Perform routine maintenance to keep equipment operating properly. Inspect systems regularly to detect wear, faults, or potential failures. Replace worn or defective parts. 3. Troubleshooting and Repair Diagnose technical issues using testing tools and diagnostic software. Repair or replace faulty components on-site. Ensure systems return to full operational condition. 4. Customer Support Communicate with customers to understand reported issues. Explain technical problems and solutions in simple terms. Provide guidance on proper equipment use and basic maintenance. 5. Documentation and Reporting Record service visits, repairs performed, and parts used. Complete service reports and update maintenance logs. Report recurring issues or product improvements to engineering teams. 6. Safety and Compliance Follow safety procedures and regulations while working on-site. Use proper tools and protective equipment. Ensure installations meet industry standards. 7. Travel and Scheduling Travel to different customer locations or job sites. Manage daily service schedules and respond to emergency service calls. 8. Inventory and Tools Management Maintain service tools and testing equipment. Keep track of spare parts and order replacements when needed

• Execute service delivery to customers and ensure job deliverables are accurate and delivered on time • Participate in job risk analysis and continual improvement programs • Assist Design and Technical Engineers with implementing technical programs and bid activities • Develop customer contacts to promote company products and services • Ensure compliance with company and regulatory standards through the Compliance Assessment Tool (CAT), self-assessments, and wellsite inspections • Lead Service Quality Meetings with customers and implement action plans to improve performance • Participate in HSE (Health, Safety, Environment) and Quality initiatives • Wear appropriate PPE and strictly follow HSE policies • Maintain required safety training and certifications • Provide backup support to Job Delivery Leads and PSD Managers as needed

1. Operational Supervision Oversee daily coiled tubing operations such as well intervention, cleanouts, acid stimulation, milling, and logging. Ensure operations follow the approved program, procedures, and engineering design. Monitor equipment performance including injector head, reel, BOP stack, control cabin, and pumping units. Coordinate with drilling supervisors, engineers, and client representatives on-site. Make real-time operational decisions during well intervention. 2. Safety Leadership Enforce HSE (Health, Safety, and Environment) standards during all operations. Conduct pre-job safety meetings (toolbox talks) and risk assessments. Ensure compliance with company and industry standards such as: American Petroleum Institute (API) International Association of Drilling Contractors (IADC) Monitor well control and pressure control equipment. Stop operations if unsafe conditions occur. 3. Team Leadership and Personnel Management Supervise coiled tubing operators, technicians, and helpers. Assign tasks and ensure proper crew rotation and competency. Train and mentor junior operators. Evaluate crew performance and maintain discipline and teamwork. 4. Equipment Management Ensure proper inspection, maintenance, and testing of coiled tubing equipment. Verify pressure testing of BOPs and control systems. Track tubing life, fatigue, and string condition. Coordinate repairs and preventive maintenance. 5. Job Planning and Coordination Review well intervention programs and procedures before the job. Prepare equipment, tools, and materials required for operations. Coordinate logistics with base, maintenance teams, and third-party services. 6. Reporting and Documentation Maintain daily operational reports. Record job parameters such as depth, pressure, weight, and pumping rates. Report incidents, downtime, and operational performance. Provide job feedback to engineering teams. 7. Quality Control Ensure work meets client specifications and company standards. Verify proper installation and testing of downhole tools. Monitor job efficiency and minimize non-productive time (NPT). 8. Emergency Response Lead the crew during well control situations or equipment failures. Implement emergency procedures and coordinate with site management. Ensure crew is trained for well control and emergency drills. ✅ Key Skills Required Strong well intervention knowledge Leadership and team management Problem-solving under pressure Safety awareness Mechanical and hydraulic system knowledge

I am an experienced oil and gas professional with several years of international field experience. I have worked in different parts of the world as a Coiled Tubing (CT) Operator, Nitrogen (N2) Pump Operator, and Fluids Pump Operator. Throughout my career, I have had the opportunity to work in multiple countries, including Colombia, Mexico, and Saudi Arabia, gaining valuable experience in diverse operational environments and conditions. During my time in the industry, I have participated in a wide range of well intervention and stimulation operations such as milling, stimulation, fishing, cementing, well cleanup, and other related services. These experiences have allowed me to develop strong technical skills, operational discipline, and the ability to work efficiently under pressure while maintaining high safety standards. I also have experience working both offshore and onshore, adapting quickly to different teams, equipment, and operational procedures. My background has helped me build a solid understanding of oilfield operations, teamwork, and problem-solving in demanding environments. I am a dedicated, reliable, and safety-focused professional who is always willing to learn and improve. Currently, I am available and ready to mobilize, and I look forward to contributing my skills and experience to a professional team in the oil and gas industry.

Industrial Electrical and Maintenance Engineer General Electrical maintenance of electrical motor. Very reliable in team support and ability to coordinate an appropriate working environment. Good communication skill and accessibility. Proper work orientation and good in delivering goal at work site. Electrical troubleshooting expact. Water treatment technician Power plant Operation and maintenance Engineer And High and low voltage technician. Air compressor technician. Industrial technician with verse maintenance approach in Engineering and Technology applying relevant skill in every maintenance related issue thereby given an output of efficiency to all electrical related issue in Industry. Demonstrates strong proficiency in PLC programming, automation, and instrumentation, with a consistent focus on safety, reliability, and operational excellence. Known for delivering cost-effective technical solutions, reducing downtime, and driving continuous improvement in line with industry stand

Key Performance Indicators Provide the best Stimulation service quality by excellence in Execution, doing it right the first time. During and after performing NZ-38 Matrix Acidizing treatment. The detailed Job safety Analysis (JSA) and Hazard and Risk Control Analysis (HARC) are to be prepared and discussed with Somoil representatives and Schlumberger Crew Evidence should be kept on location in Packet folder. I Performed Site visit as SLB FST Assists fields specialist. I Performed Site visit as SLB FST Assists fields specialist. Ensure 100% compliance to SLB KSQR/SR JRI for the Stimulation Matrix treatment. Mobilization and Rig Up: Mobilize all equipment to well. As equipment Operator Batch Mixer Operator Fluid Pumps operator I was trained to operate diverse fruids pumps from SLB SPS fluids pumps, CPS fluids pumps, FPS fluids pumps etc. Brief description of a key point responsibilities include: As equipment leader operators Preparation requirements. JS and all equipments maintenance performed Pump, Blender and PCM operators Equipment (including tools) current performed Stem-1 Stem-2 Equipment (tools and pumping) able to pump/perform job as designed (rate, volume, pressure density, etc. All treating equipment inspected/tested as per Well Services Standards police procedures requirement tools have been dressed correctly.

Coil tubing operating Coil tubing rig up rig down producers, fallow JSA,TBT, Safety producers,SOP, Crew handling, fallow supervisor and comny man producers, nitrogen operating maintain equipment, well line up emergency handling, Coil operating unit ,120k, 100k 80k 60k 40k type of unit, using equipment jerah, hydra HPT, kerui nitrogen unit using 180k, 90k, HPT, hydra, unit, prepared CT unit, using the conector,like dimple conector, external, internal, slip conector, roll-on conector, BOP tyke Qued and qumbi BOP fallow the job program as given company, job permit, prepared, fallow the pre Job-and post job Coil tubing using software jedas, job master, medco, orient coil serve,job done, milling job, clean out job, fishing job,roto jetjob,jet blaster, N2 lifting,well, activation, ESP flushing Job-,nitra five job, acid pickling JOB, acid stimulation job, SSD,job,

With over a 9 years of dedicated experience in the onshore oil and gas sector, I currently serve as a Control Room Operator (CRO) specializing in Process Gas operations. My core responsibility is managing the intricate balance of plant stability and production efficiency. I act as the central nervous system of the facility, continuously monitoring real-time data to ensure smooth, uninterrupted operations while strictly adhering to established Standard Operating Procedures (SOPs). Safety and compliance are the cornerstones of my professional conduct. I manage critical safety systems, including the administration of Permit to Work (PTW) protocols and the rigorous execution of Energy Isolation (Lock Out, Tag Out) to protect personnel and assets. My role requires seamless communication; I serve as the primary liaison, coordinating high-stakes maneuvers between Field Technicians and Site Supervisors to ensure operational alignment. Beyond the console, I am a committed member of the Emergency Response Team (ERT), prepared to lead during critical incidents. I also oversee the logistics of downstream delivery, ensuring product reaches customers safely and on schedule, while maintaining meticulous operational reports and inventory documentation. My career is defined by a culture of safety, recently culminating in the significant milestone of achieving 12 years without a Lost Time Incident (LTI) as of March 1, 2026.

Supervise job procedures as per design of service. Operate Coiled-Tubing units. Rig up & Down Coiled-Tubing, DAS, Fluid & Nitrogen pumping units. Perform Coiled-Tubing calculations during the operations. Perform Nitrogen lifting , Acid stimulation, Scale removal & Sand clean operations. Deal with Coiled-Tubing Software (IWI). Perform Nitrogen lifting , Acid stimulation, Scale removal, Sand clean & Post Frac operations. Operate Coiled-Tubing & nitrogen pumping units. Rig up & Down Coiled-Tubing, DAS, Fluid & Nitrogen pumping units. Perform Coiled-Tubing & Nitrogen calculations during the operations. Contact with client to meet the job requirement. Responsible for safety on location. Prepare job tickets & sign them from client. Prepare & send daily operation reports to office team. Supervise job procedures as per design of service. Operate Coiled-Tubing units. Rig up & Down Coiled-Tubing, DAS, Fluid & Nitrogen pumping units. Perform Coiled-Tubing calculations during the operations. Perform Nitrogen lifting , Acid stimulation, Scale removal & Sand clean operations. Deal with Coiled-Tubing Software (IWI). Perform Nitrogen lifting , Acid stimulation, Scale removal, Sand clean & Post Frac operations. Operate Coiled-Tubing & nitrogen pumping units. Rig up & Down Coiled-Tubing, DAS, Fluid & Nitrogen pumping units. Perform Coiled-Tubing & Nitrogen calculations during the operations. Contact with client to meet the job requirement. Responsible for safety on location. Prepare job tickets & sign them from client. Prepare & send daily operation reports to office team.